How to Clean Primo Water Dispenser? Eight Steps Guide!

The key to getting healthy and tasty water from your primo water dispenser is to clean it 3-4 times a year. This will help you do away with bacteria accumulated on the appliance’s parts and prevent deposits and mold. Find below some instructions on how to clean primo water dispenser.

Step 1. Unplug the dispenser

Before getting your hands explore the depths of the dispenser, turn it off and unplug it from the power source. This will prevent electroshocks and allow you move freely around the machine without getting trapped in the cord. Also, move the dispenser away from the wall to get access to its back side.

Step 2. Clean the water bottle holder

Remove the empty bottle from the top of the dispenser. Now that the water bottle holder is exposed, check it for mildew. If you notice any traces of mold or dirt, wipe them off with a kitchen rug or a paper towel. If the buildup proves a hard nut to crack, get a mix of baking soda and water and scrub the dirt off using a harsh brush. Once the grime is all gone, rinse with a wet cloth.

Step 3. Drain the reservoir

The main target in cleaning a primo water dispenser are its reservoirs. You will have to give them a deep clean, but before that, remove the water left inside them by opening the cold and hot water taps. Don’t forget to place a bucket under the faucets to collect the water and prevent spills on the floor.

Step 4. Prepare the cleaning solution

The cleaning solution has a leading role in how to clean primo water dispenser. Your best bet is to make a mixture of bleach and water or vinegar and water. Do not use mild soap as it can spoil the taste of water. Take a 5-gallon bottle (not the one that permanently sits on the dispenser). Remove the cap, fill with 2 gallons of water and 2 tablespoons of bleach or 2 cups of vinegar. Put the cap back and shake the bottle to help the ingredients blend.

Step 5. Install the spare bottle

Attach the bottle on the dispenser, plug the cord into the nearby power source and turn the device on. Let the cleaning solution get into the reservoirs, then turn the dispenser back off. Allow 10 minutes for the bleachy or vinegary mixture to take its effect on the grimy reservoirs. Both bleach and vinegar are effective fighters against mineral deposits, germs and mold, so trust them equally.

Once the time is up, drain the water from the reservoirs through the taps. Generally, the next step is rinsing the reservoirs, but if you feel that not all dirt has been removed from the first try, go on another round. Repeat Step 5 to give your dispenser a deeper clean.

Step 6. Rinse the reservoirs

Rinse the bottle and fill it with clear water. Place it back on the dispenser and turn it on to allow the water flow into the reservoirs. Allow a couple of minutes for the bleach/vinegar residue to blend with the water. Finally, drain through the faucets. Install a new bottle with water and check the taste of water. If you feel vinegar undertones, subject the reservoir to another rinsing session.

Step 7. Clean the drip guard

The drip guard keeps the cup straight under the faucet and prevents spills. Over time, it may also accumulate water chlorine deposits, dust and even mildew, which can easily pass from the cup guard to your hand. That’s why, you make people using the dispenser a big favor by cleaning the drip guard. If possible, remove the guard and rinse it under running water. Then, soak a soft cloth in cleaning solution and wipe the tray, removing the stuck-on dirt. Let it air dry, then place it back on the dispenser.

Step 8. Clean the dispenser’s exterior

It wouldn’t count for a wrong decision if you cleaned the exterior of the water dispenser too. Being touched on daily basis by those who approach it to drink a cup of water, the dispenser accumulates body oils and bacteria which can easily pass from one user to another. Moreover, if the device is located in a high-traffic area of your house or office, it inevitably gets coated with dust.

You are good to wipe off the dust once a week using a microfiber cloth or a duster. A water dispenser is smaller than a kitchen cabinet, fridge, or sofa, so you don’t have to worry about spending half of the day on dusting it. To tackle bacteria, use disinfecting wipes or a spray disinfectant and a cloth. Make sure not to spray the cord area of the dispenser, even if it’s unplugged. Again, this procedure costs you almost nothing in terms of time, so don’t avoid it.

How often to clean primo water dispenser?

The recommended cleaning cycle for primo water dispenser is once in 3-4 months. In this time, enough impurities accumulate as to impact the quality and taste of the water in a negative way. If comes wihtout saying that if the water has a musty smell, you should check the dispenser’s interior for mold before the cleaning day arrives, and clean it. When it comes to exterior cleaning, you are best off dusting and disinfecting it once a week. If the dispenser is exposed to a high traffic, you can clean it more often.

To sum up

This article comes to remove your confusion about how to clean primo water dispenser. The process is not easy, but you don’t have to do it every weekend, so maintaining the dispenser will not take you much time overall. Pay most of your attention on the reservoirs cleaning, but don’t overlook other parts. Mold and grime can accumulate anywhere inside the dispenser, so keep a keen eye when cleaning the interior. Consider exterior cleaning as well, as it can also become a hub of germs and dust that can slip into your cup of water.